Tag Archives: forced performance turbo rebuild kit

Forced Performance FP Red Turbo Rebuild Kit

9 Replies

FP Red Turbo Rebuild KitWe Offer Turbo Rebuild Kits for FP Red, Green, Black, 73 HTA, 71 HTA, 68 HTA Turbochargers. 

We Offer 2 Separate Rebuild Kits.

  • Evo 1-3 and Evo X
  • Evo 4-9

 

 

If You Need to Purchase a Turbo Rebuild Kit for an FP Turbo for a DSM, Evo 1-3 or Evo X. You Can Purchase Here:

FP Red turbo rebuild kit

 

If You Need to Purchase a Turbo Rebuild Kit for an FP Turbo for Evo 4 – 9. You Can Purchase Here:

Forced Performance Red turbo rebuild kit

 

Why Use Our Rebuild Kits?

Have You Noticed In and Out Shaft Play with Your FP and MAP Turbochargers?  I Have Seen Steel Thrust Bearings in these Turbos In the Past. Steel is not a Good Bearing Material, and the Steel Bearing Requires Zinc Rich Oil. But Even if You Use the Special Oil, You can Still Have Failures. The Steel on Steel Contact Builds Up Excessive Heat in the Cartridge, Causing the Oil to Dry Up, Which Causes the Thrust Bearing to Fail.

FP Says On their Website, that the Warranty is Void if you Push Their FP Black Over 28 PSI. With Our 100% Copper Bar Thrust Bearings, We Have People Pushing 34 PSI Daily Driven with a Turbo Lab 60mm Evo 9 Turbo, Making over 600 HP, Without Problems.  Copper Bar Dissipates Heat and is Standard Material In OEM Turbochargers.

 

MHI 14B 16g 20g Turbo Rebuild Kit

23 Replies

FP MAP Tomica Racing turbo rebuild kitMHI 14B 16g 20g Turbo Rebuild Kit Fits:

  • Evo X Turbos
  • MHI Genuine 14b,16g, 18g, 20g, FP Green, Red, Black MAP, Tomica Racing, Blouch, Turbos
  • NOT for Evo 4-9 Turbos, (Visit Here for Evo 4-9 Turbo Rebuild kit)
  • Subaru MHI 16g and Upgraded Turbos
  • Hahn Racecraft Turbos
  • Tomei Turbo

This is an Upgraded Rebuild Kit that is Needed for Running Higher Boost Levels. We Have Customers running 34 PSI on This Rebuild Kit  with the Largest Frame Turbo and Making Over 600 HP and Holding Strong!! Here Is Our Amazon Listing If You Need to Purchase:

Here are the Details of what Our Rebuild Kit Includes:

  • 1 upgraded thrust bearing
  • 1 18mm thrust collar
  • 1 18mm thrust spacer (factory is 14mm)
  • 2 journal bearings
  • 1 front seal
  • 1 rear seal
  • oring for compressor housing
  • oring for inside the turbo
  • 2 bearing retaining clips
  • 1 stainless steel rear heat shield
  • 1 c-clip to hold in the front plate.
  • 1 oil return gasket
  • 1 bolt and nut for the vband clamp
  • 1 compressor nut
  • 1 oil deflector

NOTE: **************THIS KIT DOES NOT WORK WITH KNOCKOFF TURBOS SUCH AS CX RACING OR GODSPEED!!!!!************ ONLY THE TRUE MHI TURBOS!!!!!

NOTE: This Rebuild Kit is for Standard Rotation Only (Evo 1 -3 Evo X Turbos). This Kit is not for Evo4 – 9 Turbos Because They Use a Reverse Rotation Thrust Bearing. We also Sell the Evo 4-9 Rebuild Kit Here!